Urgent leak or storm damage? Call 01842 773633 - answered day and nightUrgent leak? Call 01842 773633
Brandon Roofing Specialists
01842 773633 Get a Quote →

Lead Work in Santon Downham

Lead flashing, valley and chimney work should be carried out to BS EN 12588, and the simple aftercare that protects that work for the long term is worth knowing about.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01842 773633
Lead Work · Santon Downham

Expert Lead Work
in Santon Downham

Why aftercare matters with lead work

Lead is one of the most durable roofing materials available. When it is correctly installed, it should perform well for many decades without needing major intervention. But even good lead work can fail prematurely if basic maintenance is neglected - and in many cases, the problems that bring homeowners to need a full re-flash are entirely avoidable with straightforward routine checks.

Lead work covers the most vulnerable junctions on your roof: chimney stacks, dormer cheeks, valleys, abutments where a lean-to joins the main wall. These are the points where different building elements meet, where water is most likely to find a way in if anything goes wrong. Keeping them in good order is not complicated, but it does require looking at them periodically.

How often should you check your lead work?

A visual check from ground level once or twice a year is a sensible habit. Binoculars make this easier and safer than trying to assess from a window or a ladder. The best times are in autumn before winter sets in, and again in spring after the frost season. Look for anything that is visibly lifting, pulling away from the wall, or has changed since the previous check.

Any lead work that has been in place for more than 20 to 25 years is worth having inspected from the roof level by a roofer, even if it looks fine from the ground. Problems in the joints and fixings are not always visible from below, and catching a minor issue early is significantly cheaper than dealing with the water damage it causes if left.

What to look for during a ground-level check

  • Lifted or curling lead edges. Lead expands and contracts with temperature changes throughout the year. If it was fixed without proper clips or was laid in overlength sheets, it can lift at the edges over time. A lifted edge that is not re-fixed will allow water to track behind the flashing.
  • Gaps in pointing around the chase. Lead flashings are tucked into a slot cut in the brickwork and held in place partly by mortar pointing. If that pointing fails, the top of the flashing can pull away from the wall even if the lead itself is sound. Look for visible gaps between the lead and the brickwork above it.
  • Dark staining or tide marks on chimney breast or walls inside. A damp patch or stain on a chimney breast, particularly after rain, almost always indicates a lead failure rather than a condensation problem. Do not ignore it and hope it will dry out.
  • Moss or vegetation growing into a valley. Lead valleys collect debris, and over time moss and compacted leaves create a dam that holds water against the edges of the lead. This accelerates deterioration of the joint and can cause water to back up under adjacent tiles.
  • White or light-coloured streaking on brickwork below flashings. This is often mortar or mineral wash from the brickwork, carried down by water that is tracking where it should not be. It is not always a sign of failure, but it is worth noting and monitoring.

Simple maintenance tasks that genuinely make a difference

Keeping gutters and valleys clear of debris is the single most effective thing a homeowner can do to protect their lead work. A blocked gutter overflows onto the roof surface and forces water into junctions. A debris-filled valley holds standing water against the edges of the lead for extended periods. Both shorten the life of otherwise sound lead work.

Clear gutters at least once a year - twice if there are trees nearby. Valleys should be checked at the same time. If you can see accumulated moss or leaf matter, it needs to come out. Use a soft brush or scoop to remove it rather than a pressure washer, which can dislodge or damage the lead and the tiles around it.

Do not apply any sealant, bitumen paint, or roofing compound to lead flashings. These products may seem like a sensible additional layer of protection, but they trap movement, cause the lead to crack earlier, and make future repairs significantly more difficult. Sound lead does not need coating.

After new lead work is installed: what to expect

Freshly installed lead has a bright, silvery appearance that darkens naturally to a dull grey as it oxidises. This patination is protective and normal. It does not need to be cleaned or treated. Some homeowners are concerned that the new lead looks out of place against older surrounding materials, but the colour will even out over the first couple of seasons.

New lead may also show some surface whitening, known as white rust or lead carbonate bloom. This is a normal part of the weathering process on newly installed lead and is not a defect. It washes off with rainfall over time.

If any lead lifts or pulls away from the wall within the first few months after installation, contact the roofer immediately. Correctly fixed and clipped lead should not move. Early lifting is a sign of a fixing or clipping problem that needs to be put right.

Pointing: the part of lead work most often overlooked

The mortar pointing that holds lead into its chase is a maintenance item in its own right, independent of the condition of the lead itself. Even well-installed lead will eventually suffer if the pointing around the chase fails and is not replaced. On chimney stacks, the pointing is exposed to frost, rain and the thermal movement of the stack throughout the year, and it needs periodic inspection and repointing.

If repointing is needed, it should be done with a suitable mortar mix - a traditional sand and lime mix rather than a hard, dense cement, which is too rigid for the movement that occurs around a chimney. Using an overly strong cement mix is a common cause of fresh cracking in both the mortar and the lead above it.

When to call a roofer rather than wait

Minor surface changes to lead, such as slight darkening, patination or surface whitening, are normal and do not need attention. But certain signs warrant getting someone up on the roof promptly rather than waiting for the next routine check:

  • Any visible water staining or damp inside the property near a chimney or dormer
  • Lead that is visibly cracked across its face rather than just at a joint
  • Any flashing that is clearly no longer in contact with the wall or roof surface
  • A valley that is heavily packed with debris and cannot be cleared from ground level
  • Missing mortar pointing that leaves a visible gap above the lead

Catching these early avoids the water damage to ceilings, timbers and internal plasterwork that follows from an ignored leak. The cost of dealing with the internal damage is almost always higher than the cost of the lead repair that would have prevented it.

Lead work aftercare in Santon Downham: the short version

Keep valleys and gutters clear, check the lead and its pointing annually, and call a roofer promptly if anything changes. Do not coat or patch the lead yourself. Good lead work, looked after simply, will last far longer than lead that is ignored until it fails. Call us to arrange a roof survey and we will give you an honest assessment of your lead work's current condition and what, if anything, it needs.

Why choose Brandon Roofers?

  • Free survey and itemised quote
  • Fixed price - no surprises
  • Local team

Get your free quote

No obligation · We'll call you to arrange a free visit

By submitting you agree to being contacted about your enquiry. No spam, ever.

Urgent leak or storm damage?

Call any time. Calls are answered day and night and passed straight to our roofers.

Call now: 01842 773633